banner



Home  ›  How To Put A Ukulele Strap On A Ukulele

How To Put A Ukulele Strap On A Ukulele

Written By Friday 30 December 2022 Add Comment Edit

Download Article

Download Article

The ukulele is a bright, fun musical instrument that'southward easy to comport around with yous. While yous can hold and play your ukulele at the aforementioned time, straps offer a lot of liberty in how y'all tin can play your instrument. It's usually all-time to use a ukulele strap whenever yous play, as guitar straps can be a bit too beefy.[ane] Thankfully, it takes fewer than 10 minutes to install a strap on your instrument, and so yous can become back to making music!

  1. one

    Measure the bottom of your ukulele to find the center point. Flip your ukulele over and then the thick, bottom section of the instrument is facing up. Place a ruler or measuring record vertically along the musical instrument, then discover the center point along the base of your ukulele.[2]

    • For instance, if the base of operations of your ukulele is only two in (5.1 cm) wide, mark along the i in (2.5 cm) betoken.
    • Some players prefer to only use 1 button along the bottom of their instrument.

  2. 2

    Mark the central indicate of the musical instrument with a minor notch. Use a nail or other abrupt item to marker the eye. Ideally, attempt to center this marker between the 2d and tertiary strings on your ukulele.[three]

    • Double-check that your measurement is right earlier marking your instrument.

    Ad

  3. iii

    Drill a 1⁄4  in (0.64 cm) into the marked spot with a ane⁄16  in (0.xvi cm) drill bit. Attach a really thin drill scrap to an electric drill so your push can fit properly.[4]

    • It may help to wrap a piece of tape nigh 1⁄4  in (0.64 cm) down your drill chip so y'all don't drill too far into your instrument.

  4. 4

    Screw a metal push into your ukulele with a Phillips-head screwdriver. Slide the ukulele button onto a 1⁄four  in (0.64 cm) screw, then slide a felt washer beneath the button. Adapt the button, screw, and washer on top of the hole, then use a Phillips-head screwdriver to tighten the push into the instrument.[v]

    • You can also use a Phillips-caput caput drill bit on your electric drill if you desire to speed up the process.[half dozen]
    • You can detect button straps online or at nigh music supply stores. These packages volition come with buttons, felt washers, and screws for installation.

  5. v

    Mark a spot behind the ii highest strings on the dorsum of the ukulele neck. Flip your musical instrument over gently and place information technology on a sturdy, padded surface. Find a spot behind the 2 highest strings of your instrument along the back of the ukulele cervix, focusing on the left side. Lightly marking your desired button spot with a nail so you tin can recollect where to drill.[7]

    • You don't need to do whatsoever exact measurements for this, equally long as the button goes on the base of the ukulele neck.

  6. six

    Drill about ane⁄4  in (0.64 cm) into the marked spot. Take your electrical drill and add another small hole to your instrument. Merely drill nigh one⁄iv  in (0.64 cm) into your instrument, every bit y'all don't desire to drill all the way through.[eight]

    • Since you're working along the back of the cervix, you may want to drill at an bending.[9]

  7. 7

    Secure the second button with a Phillips-head screwdriver. Slide the push onto the screw, followed past the felt washer. Center the spiral on top of the drilled hole, and then tighten information technology into place with a Phillips-head screwdriver.[ten]

  8. 8

    Connect the strap to the buttons so you can wear your ukulele. Search forth both ends of your ukulele straps for circular openings. Secure both ends along the top and bottom buttons of your ukulele to hold it in place. One time the strap is secure, loop it behind your cervix and then you tin play your musical instrument![xi]

    9. Advertisement

  1. 1

    Necktie your hug strap about the tuning pegs of the ukulele. Await for the thin, black portion along the end of the hug strap, also known as a headstock strap. Remove whatsoever prophylactic washers from this strap, and so necktie information technology beneath the strings along the acme of the ukulele neck.[12]

    • Make sure that the strap is below the strings, and not in a higher place them.

  2. 2

    Loop the thicker section of the strap about the body of the ukulele. Unthread the majority of the hug strap from any buckles and so it'due south completely straight, then wrap it around the center of the musical instrument. At this fourth dimension, check and make certain that your hug strap isn't roofing the main opening of your ukulele.[xiii]

    • If you have a thicker, pineapple-shaped ukulele, a hug strap might non be a viable choice for you.

  3. 3

    Thread the strap into the foursquare buckle to tighten it. Later on pulling it through the buckle, bank check that the strap is really taut and secure so your instrument doesn't movement around a lot while you play. Additionally, double-check that the strap isn't completely roofing the center opening on your instrument, or else your music may not be as clear and loud.[14]

  4. 4

    Connect your hug strap to ane of your ukulele buttons. Loop the headstock strap next to the tuning pegs to attach it around the elevation of your ukulele. Find a pocket-size, looped parachute cord at the bottom of your hug strap and secure it effectually the bottom button on your instrument. Equally a finishing touch, place a rubber washer on pinnacle of the button to brand your strap secure.[xv]

  5. 5

    Attach the hug strap to 2 ukulele buttons if you have them. Remove the thin, upper strap and rubber washers from the rest hug strap and discover the small, looped parachute cord attached to the cease of the hug strap. Loop this cord over the metal button on the neck of your instrument, then cover the superlative of the button with a safe washer. Search along the bottom of your headstock strap for another looped parachute cord, so attach this to the bottom of your instrument, along with another rubber washer.[xvi]

    6. Advertisement

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advert

  • Ukulele leashes are a smashing, hassle-complimentary alternative for ukulele players who don't desire to deal with buttons. Necktie i section of the strap to the headstock of your instrument next to your tuning pegs, and then loop the circular portion of the strap around your strumming arm. The bulk of the strap should be going effectually your neck.[17]

Thanks for submitting a tip for review!

Advertizement

Things You'll Need

  • Measuring tape
  • Sharp tool
  • Electric drill
  • 2 ukulele buttons
  • 2 i⁄iv  in (0.64 cm) screws
  • ii felt washers
  • Ukulele strap

About This Article

Thank you to all authors for creating a page that has been read 13,186 times.

Did this article assist yous?

Source: https://www.wikihow.com/Put-on-a-Ukulele-Strap

0 Response to "How To Put A Ukulele Strap On A Ukulele"

Post a Comment

Subscribe to: Post Comments (Atom)

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel